RTEMS 6.1-rc4
|
NXP LPC17XX, LPC23XX, LPC24XX and LPC40XX Board Support Package. More...
Modules | |
DMA Support | |
DMA support. | |
DMA Support | |
Direct memory access (DMA) support. | |
EMC Support | |
EMC Support. | |
I2C Driver | |
I2S Support | |
I2S support. | |
IO Support and Configuration | |
Input and output module. | |
LCD Support | |
LCD support. | |
Register Definitions | |
Register definitions. | |
SSP Driver | |
System Clocks | |
System clocks. | |
Timer Support | |
Timer support. | |
Files | |
file | console-config.c |
Console configuration. | |
file | uart-probe-1.c |
UART 1 probe. | |
file | uart-probe-2.c |
UART 2 probe. | |
file | uart-probe-3.c |
UART 3 probe. | |
file | bsp.h |
Global BSP definitions. | |
file | lpc-clock-config.h |
Clock driver configuration. | |
file | lpc-ethernet-config.h |
Ethernet driver configuration. | |
file | start-config.h |
BSP start configuration. | |
file | rtc-config.c |
RTC configuration. | |
file | bspidle.c |
Idle task. | |
file | bspreset-armv4.c |
Reset code. | |
file | bspstart.c |
Startup code. | |
file | bspstarthooks.c |
Startup code. | |
file | restart.c |
Restart implementation. | |
file | start-config-emc-dynamic.c |
BSP start EMC dynamic memory configuration. | |
file | start-config-emc-static.c |
BSP start EMC static memory configuration. | |
file | start-config-mpu.c |
BSP start MPU configuration. | |
file | start-config-pinsel.c |
BSP start pin selection configuration. | |
file | timer.c |
Benchmark timer support. | |
Macros | |
#define | BSP_FEATURE_IRQ_EXTENSION |
#define | LPC24XX_PCLK (LPC24XX_CCLK / LPC24XX_PCLKDIV) |
#define | LPC24XX_EMCCLK (LPC24XX_CCLK / LPC24XX_EMCCLKDIV) |
#define | LPC24XX_MPU_REGION_COUNT 8 |
#define | BSP_ARMV7M_IRQ_PRIORITY_DEFAULT (29 << 3) |
#define | BSP_ARMV7M_SYSTICK_PRIORITY (30 << 3) |
#define | BSP_ARMV7M_SYSTICK_FREQUENCY LPC24XX_CCLK |
#define | RTEMS_BSP_NETWORK_DRIVER_ATTACH lpc_eth_attach_detach |
Standard network driver attach and detach function. | |
#define | RTEMS_BSP_NETWORK_DRIVER_NAME "eth0" |
Standard network driver name. | |
#define | BSP_CONSOLE_UART_BASE 0x4000c000 |
Functions | |
int | lpc_eth_attach_detach (struct rtems_bsdnet_ifconfig *config, int attaching) |
Network driver attach and detach function. | |
void * | bsp_idle_thread (uintptr_t ignored) |
Optimized idle task. | |
void | bsp_restart (void *addr) |
bool | lpc24xx_uart_probe_1 (struct rtems_termios_device_context *context) |
bool | lpc24xx_uart_probe_2 (struct rtems_termios_device_context *context) |
bool | lpc24xx_uart_probe_3 (struct rtems_termios_device_context *context) |
NXP LPC17XX, LPC23XX, LPC24XX and LPC40XX Board Support Package.
void * bsp_idle_thread | ( | uintptr_t | ignored | ) |
Optimized idle task.
This idle task sets the power mode to idle. This causes the processor clock to be stopped, while on-chip peripherals remain active. Any enabled interrupt from a peripheral or an external interrupt source will cause the processor to resume execution.
To enable the idle task use the following in the system configuration:
This idle task sets the power mode to idle. This causes the processor clock to be stopped, while on-chip peripherals remain active. Any enabled interrupt from a peripheral or an external interrupt source will cause the processor to resume execution.
To enable the idle task use the following in the system configuration:
Optimized idle task.
The MSR[POW] bit is set to put the CPU into the low power mode defined in HID0. HID0 is set during starup in start.S.
This idle task sets the power mode to idle. This causes the processor clock to be stopped, while on-chip peripherals remain active. Any enabled interrupt from a peripheral or an external interrupt source will cause the processor to resume execution.
To enable the idle task use the following in the system configuration:
Optimized idle task.
The MSR[POW] bit is set to put the CPU into the low power mode defined in HID0. HID0 is set during starup in start.S.