qsm.h

Go to the documentation of this file.

 
/*
 * This file was created by John S. Gwynne to support Motorola's 68332 MCU.
 *
 * Redistribution and use in source and binary forms are permitted
 * provided that the following conditions are met:
 * 1. Redistribution of source code and documentation must retain
 *    the above authorship, this list of conditions and the
 *    following disclaimer.
 * 2. The name of the author may not be used to endorse or promote
 *    products derived from this software without specific prior
 *    written permission.
 *
 * This software is provided "AS IS" without warranty of any kind,
 * either expressed or implied, including, but not limited to, the
 * implied warranties of merchantability, title and fitness for a
 * particular purpose.
 *
 *------------------------------------------------------------------
 */
 
#ifndef _RTEMS_M68K_QSM_H
#define _RTEMS_M68K_QSM_H
 
/* SAM-- shift and mask */
#undef  SAM
#define SAM(a,b,c) ((a << b) & c)
 
 
/* QSM_CRB (QSM Control Register Block) base address of the QSM
   control registers */
#if SIM_MM == 0
#define QSM_CRB 0x7ffc00
#else
#undef SIM_MM
#define SIM_MM 1
#define QSM_CRB 0xfffc00
#endif
 
 
#define QSMCR (volatile unsigned short int * const)(0x00 + QSM_CRB)
                /* QSM Configuration Register */
#define    STOP 0x8000      /*    Stop Enable */
#define    FRZ  0x6000      /*    Freeze Control */
#define    SUPV 0x0080      /*    Supervisor/Unrestricted */
#define    IARB 0x000f      /*    Inerrupt Arbitration */
 
 
#define QTEST (volatile unsigned short int * const)(0x02 + QSM_CRB)
                /* QSM Test Register */
/* Used only for factor testing */
 
 
#define QILR (volatile unsigned char * const)(0x04 + QSM_CRB)
                /* QSM Interrupt Level Register */
#define    ILQSPI 0x38      /*    Interrupt Level for QSPI */
#define    ILSCI  0x07      /*    Interrupt Level for SCI */
 
 
#define QIVR (volatile unsigned char * const)(0x05 + QSM_CRB)
                /* QSM Interrupt Vector Register */
#define    INTV   0xff      /*    Interrupt Vector Number */
 
 
#define SCCR0 (volatile unsigned short int * const)(0x08 + QSM_CRB)
                /* SCI Control Register 0 */
#define    SCBR   0x1fff    /*    SCI Baud Rate */
 
 
#define SCCR1 (volatile unsigned short int * const)(0x0a + QSM_CRB)
                /* SCI Control Register 1 */
#define    LOOPS  0x4000    /*    Loop Mode */
#define    WOMS   0x2000    /*    Wired-OR Mode for SCI Pins */
#define    ILT    0x1000    /*    Idle-Line Detect Type */
#define    PT     0x0800    /*    Parity Type */
#define    PE     0x0400    /*    Parity Enable */
#define    M      0x0200    /*    Mode Select */
#define    WAKE   0x0100    /*    Wakeup by Address Mark */
#define    TIE    0x0080    /*    Transmit Complete Interrupt Enable */
#define    TCIE   0x0040    /*    Transmit Complete Interrupt Enable */
#define    RIE    0x0020    /*    Receiver Interrupt Enable */
#define    ILIE   0x0010    /*    Idle-Line Interrupt Enable */
#define    TE     0x0008    /*    Transmitter Enable */
#define    RE     0x0004    /*    Receiver Enable */
#define    RWU    0x0002    /*    Receiver Wakeup */
#define    SBK    0x0001    /*    Send Break */
 
 
#define SCSR (volatile unsigned short int * const)(0x0c + QSM_CRB)
                /* SCI Status Register */
#define    TDRE   0x0100    /*    Transmit Data Register Empty */
#define    TC     0x0080    /*    Transmit Complete */
#define    RDRF   0x0040    /*    Receive Data Register Full */
#define    RAF    0x0020    /*    Receiver Active */
#define    IDLE   0x0010    /*    Idle-Line Detected */
#define    OR     0x0008    /*    Overrun Error */
#define    NF     0x0004    /*    Noise Error Flag */
#define    FE     0x0002    /*    Framing Error */
#define    PF     0x0001    /*    Parity Error */
 
 
#define SCDR (volatile unsigned short int * const)(0x0e + QSM_CRB)
                /* SCI Data Register */
 
 
#define PORTQS (volatile unsigned char * const)(0x15 + QSM_CRB)
                /* Port QS Data Register */
 
#define PQSPAR (volatile unsigned char * const)(0x16 + QSM_CRB)
                /* PORT QS Pin Assignment Rgister */
/* Any bit cleared (zero) defines the corresponding pin to be an I/O
   pin. Any bit set defines the corresponding pin to be a QSPI
   signal. */
/* note: PQS2 is a digital I/O pin unless the SPI is enabled in which
   case it becomes the SPI serial clock SCK. */
/* note: PQS7 is a digital I/O pin unless the SCI transmitter is
   enabled in which case it becomes the SCI serial output TxD. */
#define QSMFun 0x0
#define QSMDis 0x1
/*
 * PQSPAR Field     | QSM Function | Discrete I/O pin
 *------------------+--------------+------------------   */
#define PQSPA0   0  /*   MISO      |      PQS0           */
#define PQSPA1   1  /*   MOSI      |      PQS1           */
#define PQSPA2   2  /*   SCK       |      PQS2 (see note)*/
#define PQSPA3   3  /*   PCSO/!SS  |      PQS3           */
#define PQSPA4   4  /*   PCS1      |      PQS4           */
#define PQSPA5   5  /*   PCS2      |      PQS5           */
#define PQSPA6   6  /*   PCS3      |      PQS6           */
#define PQSPA7   7  /*   TxD       |      PQS7 (see note)*/
 
 
#define DDRQS  (volatile unsigned char * const)(0x17 + QSM_CRB)
                /* PORT QS Data Direction Register */
/* Clearing a bit makes the corresponding pin an input; setting a bit
   makes the pin an output. */
 
 
#define SPCR0 (volatile unsigned short int * const)(0x18 + QSM_CRB)
                /* QSPI Control Register 0 */
#define    MSTR   0x8000    /*    Master/Slave Mode Select */
#define    WOMQ   0x4000    /*    Wired-OR Mode for QSPI Pins */
#define    BITS   0x3c00    /*    Bits Per Transfer */
#define    CPOL   0x0200    /*    Clock Polarity */
#define    CPHA   0x0100    /*    Clock Phase */
#define    SPBR   0x00ff    /*    Serial Clock Baud Rate */
 
 
#define SPCR1 (volatile unsigned short int * const)(0x1a + QSM_CRB)
                /* QSPI Control Register 1 */
#define    SPE    0x8000    /*    QSPI Enable */
#define    DSCKL  0x7f00    /*    Delay before SCK */
#define    DTL    0x00ff    /*    Length of Delay after Transfer */
 
 
#define SPCR2 (volatile unsigned short int * const)(0x1c + QSM_CRB)
                /* QSPI Control Register 2 */
#define    SPIFIE 0x8000    /*    SPI Finished Interrupt Enable */
#define    WREN   0x4000    /*    Wrap Enable */
#define    WRTO   0x2000    /*    Wrap To */
#define    ENDQP  0x0f00    /*    Ending Queue Pointer */
#define    NEWQP  0x000f    /*    New Queue Pointer Value */
 
 
#define SPCR3 (volatile unsigned char * const)(0x1e + QSM_CRB)
                /* QSPI Control Register 3 */
#define    LOOPQ  0x0400    /*    QSPI Loop Mode */
#define    HMIE   0x0200    /*    HALTA and MODF Interrupt Enable */
#define    HALT   0x0100    /*    Halt */
 
 
#define SPSR (volatile unsigned char * const)(0x1f + QSM_CRB)
                /* QSPI Status Register */
#define    SPIF   0x0080    /*    QSPI Finished Flag */
#define    MODF   0x0040    /*    Mode Fault Flag */
#define    HALTA  0x0020    /*    Halt Acknowlwdge Flag */
#define    CPTQP  x0000f    /*    Completed Queue Pointer */
 
#define QSPIRR (volatile unsigned char * const)(0x100 + QSM_CRB)
                /* QSPI Receive Data RAM */
#define QSPITR (volatile unsigned char * const)(0x120 + QSM_CRB)
                /* QSPI Transmit Data RAM */
#define QSPIcR (volatile unsigned char * const)(0x140 + QSM_CRB)
                /* QSPI Command RAM */
 
#endif /* _RTEMS_M68K_QSM_H */