This file contains all the functions prototypes for the HAL module driver. More...

#include "stm32h7xx_hal_conf.h"

Macros
#define	REV_ID_Y ((uint32_t)0x1003)

#define	REV_ID_B ((uint32_t)0x2000)

#define	REV_ID_X ((uint32_t)0x2001)

#define	REV_ID_V ((uint32_t)0x2003)

#define	SYSCFG_VREFBUF_VOLTAGE_SCALE0 VREFBUF_CSR_VRS_OUT1

#define	SYSCFG_VREFBUF_VOLTAGE_SCALE1 VREFBUF_CSR_VRS_OUT2

#define	SYSCFG_VREFBUF_VOLTAGE_SCALE2 VREFBUF_CSR_VRS_OUT3

#define	SYSCFG_VREFBUF_VOLTAGE_SCALE3 VREFBUF_CSR_VRS_OUT4

#define	IS_SYSCFG_VREFBUF_VOLTAGE_SCALE(__SCALE__)

#define	SYSCFG_VREFBUF_HIGH_IMPEDANCE_DISABLE ((uint32_t)0x00000000)

#define	SYSCFG_VREFBUF_HIGH_IMPEDANCE_ENABLE VREFBUF_CSR_HIZ

#define	IS_SYSCFG_VREFBUF_HIGH_IMPEDANCE(__VALUE__)

#define	IS_SYSCFG_VREFBUF_TRIMMING(__VALUE__) (((__VALUE__) > 0UL) && ((__VALUE__) <= VREFBUF_CCR_TRIM))

#define	SYSCFG_FASTMODEPLUS_PB6 SYSCFG_PMCR_I2C_PB6_FMP
	Fast-mode Plus driving capability on a specific GPIO.

#define	SYSCFG_FASTMODEPLUS_PB7 SYSCFG_PMCR_I2C_PB7_FMP

#define	SYSCFG_FASTMODEPLUS_PB8 SYSCFG_PMCR_I2C_PB8_FMP

#define	SYSCFG_FASTMODEPLUS_PB9 SYSCFG_PMCR_I2C_PB9_FMP

#define	IS_SYSCFG_FASTMODEPLUS(__PIN__)

#define	SYSCFG_ETH_MII ((uint32_t)0x00000000)

#define	SYSCFG_ETH_RMII SYSCFG_PMCR_EPIS_SEL_2

#define	IS_SYSCFG_ETHERNET_CONFIG(CONFIG)

#define	SYSCFG_SWITCH_PA0 SYSCFG_PMCR_PA0SO

#define	SYSCFG_SWITCH_PA1 SYSCFG_PMCR_PA1SO

#define	SYSCFG_SWITCH_PC2 SYSCFG_PMCR_PC2SO

#define	SYSCFG_SWITCH_PC3 SYSCFG_PMCR_PC3SO

#define	SYSCFG_SWITCH_PA0_OPEN SYSCFG_PMCR_PA0SO

#define	SYSCFG_SWITCH_PA0_CLOSE ((uint32_t)0x00000000)

#define	SYSCFG_SWITCH_PA1_OPEN SYSCFG_PMCR_PA1SO

#define	SYSCFG_SWITCH_PA1_CLOSE ((uint32_t)0x00000000)

#define	SYSCFG_SWITCH_PC2_OPEN SYSCFG_PMCR_PC2SO

#define	SYSCFG_SWITCH_PC2_CLOSE ((uint32_t)0x00000000)

#define	SYSCFG_SWITCH_PC3_OPEN SYSCFG_PMCR_PC3SO

#define	SYSCFG_SWITCH_PC3_CLOSE ((uint32_t)0x00000000)

#define	IS_SYSCFG_ANALOG_SWITCH(SWITCH)

#define	IS_SYSCFG_SWITCH_STATE(STATE)

#define	SYSCFG_BOOT_ADDR0 ((uint32_t)0x00000000)

#define	SYSCFG_BOOT_ADDR1 ((uint32_t)0x00000001)

#define	IS_SYSCFG_BOOT_REGISTER(REGISTER)

#define	IS_SYSCFG_BOOT_ADDRESS(ADDRESS) ((ADDRESS) < PERIPH_BASE)

#define	SYSCFG_CELL_CODE ((uint32_t)0x00000000)

#define	SYSCFG_REGISTER_CODE SYSCFG_CCCSR_CS

#define	IS_SYSCFG_CODE_SELECT(SELECT)

#define	IS_SYSCFG_CODE_CONFIG(CONFIG) ((CONFIG) < (0x10UL))

#define	EXTI_MODE_IT ((uint32_t)0x00010000)

#define	EXTI_MODE_EVT ((uint32_t)0x00020000)

#define	EXTI_RISING_EDGE ((uint32_t)0x00100000)

#define	EXTI_FALLING_EDGE ((uint32_t)0x00200000)

#define	IS_EXTI_EDGE_LINE(EDGE) (((EDGE) == EXTI_RISING_EDGE) \|\| ((EDGE) == EXTI_FALLING_EDGE))

#define	IS_EXTI_MODE_LINE(MODE) (((MODE) == EXTI_MODE_IT) \|\| ((MODE) == EXTI_MODE_EVT))

#define	EXTI_LINE0 ((uint32_t)0x00)

#define	EXTI_LINE1 ((uint32_t)0x01)

#define	EXTI_LINE2 ((uint32_t)0x02)

#define	EXTI_LINE3 ((uint32_t)0x03)

#define	EXTI_LINE4 ((uint32_t)0x04)

#define	EXTI_LINE5 ((uint32_t)0x05)

#define	EXTI_LINE6 ((uint32_t)0x06)

#define	EXTI_LINE7 ((uint32_t)0x07)

#define	EXTI_LINE8 ((uint32_t)0x08)

#define	EXTI_LINE9 ((uint32_t)0x09)

#define	EXTI_LINE10 ((uint32_t)0x0A)

#define	EXTI_LINE11 ((uint32_t)0x0B)

#define	EXTI_LINE12 ((uint32_t)0x0C)

#define	EXTI_LINE13 ((uint32_t)0x0D)

#define	EXTI_LINE14 ((uint32_t)0x0E)

#define	EXTI_LINE15 ((uint32_t)0x0F)

#define	EXTI_LINE16 ((uint32_t)0x10)

#define	EXTI_LINE17 ((uint32_t)0x11)

#define	EXTI_LINE18 ((uint32_t)0x12)

#define	EXTI_LINE19 ((uint32_t)0x13)

#define	EXTI_LINE20 ((uint32_t)0x14)

#define	EXTI_LINE21 ((uint32_t)0x15)

#define	EXTI_LINE22 ((uint32_t)0x16)

#define	EXTI_LINE23 ((uint32_t)0x17)

#define	EXTI_LINE24 ((uint32_t)0x18)

#define	EXTI_LINE25 ((uint32_t)0x19)

#define	EXTI_LINE26 ((uint32_t)0x1A)

#define	EXTI_LINE27 ((uint32_t)0x1B)

#define	EXTI_LINE28 ((uint32_t)0x1C)

#define	EXTI_LINE29 ((uint32_t)0x1D)

#define	EXTI_LINE30 ((uint32_t)0x1E)

#define	EXTI_LINE31 ((uint32_t)0x1F)

#define	EXTI_LINE32 ((uint32_t)0x20)

#define	EXTI_LINE33 ((uint32_t)0x21)

#define	EXTI_LINE34 ((uint32_t)0x22)

#define	EXTI_LINE35 ((uint32_t)0x23)

#define	EXTI_LINE36 ((uint32_t)0x24)

#define	EXTI_LINE37 ((uint32_t)0x25)

#define	EXTI_LINE38 ((uint32_t)0x26)

#define	EXTI_LINE39 ((uint32_t)0x27)

#define	EXTI_LINE40 ((uint32_t)0x28)

#define	EXTI_LINE41 ((uint32_t)0x29)

#define	EXTI_LINE42 ((uint32_t)0x2A)

#define	EXTI_LINE43 ((uint32_t)0x2B)

#define	EXTI_LINE44 ((uint32_t)0x2C) /* Not available in all family lines */

#define	EXTI_LINE47 ((uint32_t)0x2F)

#define	EXTI_LINE48 ((uint32_t)0x30)

#define	EXTI_LINE49 ((uint32_t)0x31)

#define	EXTI_LINE50 ((uint32_t)0x32)

#define	EXTI_LINE51 ((uint32_t)0x33)

#define	EXTI_LINE52 ((uint32_t)0x34)

#define	EXTI_LINE53 ((uint32_t)0x35)

#define	EXTI_LINE54 ((uint32_t)0x36)

#define	EXTI_LINE55 ((uint32_t)0x37)

#define	EXTI_LINE56 ((uint32_t)0x38)

#define	EXTI_LINE57 ((uint32_t)0x39)

#define	EXTI_LINE58 ((uint32_t)0x3A)

#define	EXTI_LINE59 ((uint32_t)0x3B)

#define	EXTI_LINE60 ((uint32_t)0x3C)

#define	EXTI_LINE61 ((uint32_t)0x3D)

#define	EXTI_LINE62 ((uint32_t)0x3E)

#define	EXTI_LINE63 ((uint32_t)0x3F)

#define	EXTI_LINE64 ((uint32_t)0x40)

#define	EXTI_LINE65 ((uint32_t)0x41)

#define	EXTI_LINE66 ((uint32_t)0x42)

#define	EXTI_LINE67 ((uint32_t)0x43)

#define	EXTI_LINE68 ((uint32_t)0x44)

#define	EXTI_LINE69 ((uint32_t)0x45)

#define	EXTI_LINE70 ((uint32_t)0x46)

#define	EXTI_LINE71 ((uint32_t)0x47)

#define	EXTI_LINE72 ((uint32_t)0x48)

#define	EXTI_LINE73 ((uint32_t)0x49)

#define	EXTI_LINE74 ((uint32_t)0x4A)

#define	EXTI_LINE75 ((uint32_t)0x4B) /* Not available in all family lines */

#define	EXTI_LINE76 ((uint32_t)0x4C) /* Not available in all family lines */

#define	EXTI_LINE85 ((uint32_t)0x55)

#define	EXTI_LINE86 ((uint32_t)0x56) /* Not available in all family lines */

#define	EXTI_LINE87 ((uint32_t)0x57)

#define	EXTI_LINE88 ((uint32_t)0x58) /* Not available in all family lines */

#define	EXTI_LINE89 ((uint32_t)0x59) /* Not available in all family lines */

#define	EXTI_LINE90 ((uint32_t)0x5A) /* Not available in all family lines */

#define	EXTI_LINE91 ((uint32_t)0x5B) /* Not available in all family lines */

#define	IS_HAL_EXTI_CONFIG_LINE(LINE)

#define	IS_EXTI_ALL_LINE(LINE)

#define	IS_EXTI_D1_LINE(LINE)

#define	IS_EXTI_D3_LINE(LINE)

#define	BDMA_CH6_CLEAR ((uint32_t)0x00000000)

#define	BDMA_CH7_CLEAR ((uint32_t)0x00000001)

#define	LPTIM2_OUT_CLEAR ((uint32_t)0x00000002)

#define	LPTIM3_OUT_CLEAR ((uint32_t)0x00000003)

#define	IS_EXTI_D3_CLEAR(SOURCE)

#define	FMC_SWAPBMAP_DISABLE (0x00000000U)

#define	FMC_SWAPBMAP_SDRAM_SRAM FMC_BCR1_BMAP_0

#define	FMC_SWAPBMAP_SDRAMB2 FMC_BCR1_BMAP_1

#define	IS_FMC_SWAPBMAP_MODE(__MODE__)

#define	__HAL_SYSCFG_BREAK_AXISRAM_DBL_ECC_LOCK() SET_BIT(SYSCFG->CFGR, SYSCFG_CFGR_AXISRAML)
	SYSCFG Break AXIRAM double ECC lock. Enable and lock the connection of AXIRAM double ECC error to TIM1/8/15/16/17 and HRTIMER Break input.

#define	__HAL_SYSCFG_BREAK_ITCM_DBL_ECC_LOCK() SET_BIT(SYSCFG->CFGR, SYSCFG_CFGR_ITCML)
	SYSCFG Break ITCM double ECC lock. Enable and lock the connection of ITCM double ECC error to TIM1/8/15/16/17 and HRTIMER Break input.

#define	__HAL_SYSCFG_BREAK_DTCM_DBL_ECC_LOCK() SET_BIT(SYSCFG->CFGR, SYSCFG_CFGR_DTCML)
	SYSCFG Break DTCM double ECC lock. Enable and lock the connection of DTCM double ECC error to TIM1/8/15/16/17 and HRTIMER Break input.

#define	__HAL_SYSCFG_BREAK_SRAM1_DBL_ECC_LOCK() SET_BIT(SYSCFG->CFGR, SYSCFG_CFGR_SRAM1L)
	SYSCFG Break SRAM1 double ECC lock. Enable and lock the connection of SRAM1 double ECC error to TIM1/8/15/16/17 and HRTIMER Break input.

#define	__HAL_SYSCFG_BREAK_SRAM2_DBL_ECC_LOCK() SET_BIT(SYSCFG->CFGR, SYSCFG_CFGR_SRAM2L)
	SYSCFG Break SRAM2 double ECC lock. Enable and lock the connection of SRAM2 double ECC error to TIM1/8/15/16/17 and HRTIMER Break input.

#define	__HAL_SYSCFG_BREAK_SRAM3_DBL_ECC_LOCK() SET_BIT(SYSCFG->CFGR, SYSCFG_CFGR_SRAM3L)
	SYSCFG Break SRAM3 double ECC lock. Enable and lock the connection of SRAM3 double ECC error to TIM1/8/15/16/17 and HRTIMER Break input.

#define	__HAL_SYSCFG_BREAK_SRAM4_DBL_ECC_LOCK() SET_BIT(SYSCFG->CFGR, SYSCFG_CFGR_SRAM4L)
	SYSCFG Break SRAM4 double ECC lock. Enable and lock the connection of SRAM4 double ECC error to TIM1/8/15/16/17 and HRTIMER Break input.

#define	__HAL_SYSCFG_BREAK_BKRAM_DBL_ECC_LOCK() SET_BIT(SYSCFG->CFGR, SYSCFG_CFGR_BKRAML)
	SYSCFG Break Backup SRAM double ECC lock. Enable and lock the connection of Backup SRAM double ECC error to TIM1/8/15/16/17 and HRTIMER Break input.

#define	__HAL_SYSCFG_BREAK_CM7_LOCKUP_LOCK() SET_BIT(SYSCFG->CFGR, SYSCFG_CFGR_CM7L)
	SYSCFG Break Cortex-M7 Lockup lock. Enable and lock the connection of Cortex-M7 LOCKUP output to TIM1/8/15/16/17 and HRTIMER Break input.

#define	__HAL_SYSCFG_BREAK_FLASH_DBL_ECC_LOCK() SET_BIT(SYSCFG->CFGR, SYSCFG_CFGR_FLASHL)
	SYSCFG Break FLASH double ECC lock. Enable and lock the connection of Flash double ECC error connection to TIM1/8/15/16/17 and HRTIMER Break input.

#define	__HAL_SYSCFG_BREAK_PVD_LOCK() SET_BIT(SYSCFG->CFGR, SYSCFG_CFGR_PVDL)
	SYSCFG Break PVD lock. Enable and lock the PVD connection to Timer1/8/15/16/17 and HRTIMER Break input, as well as the PVDE and PLS[2:0] in the PWR_CR1 register.

#define	__HAL_SYSCFG_FASTMODEPLUS_ENABLE(__FASTMODEPLUS__)
	Fast-mode Plus driving capability enable/disable macros.

#define	__HAL_SYSCFG_FASTMODEPLUS_DISABLE(__FASTMODEPLUS__)

#define	__HAL_DBGMCU_FREEZE_WWDG1() (DBGMCU->APB3FZ1 \|= (DBGMCU_APB3FZ1_DBG_WWDG1))
	Freeze/Unfreeze Peripherals in Debug mode.

#define	__HAL_DBGMCU_FREEZE_TIM2() (DBGMCU->APB1LFZ1 \|= (DBGMCU_APB1LFZ1_DBG_TIM2))

#define	__HAL_DBGMCU_FREEZE_TIM3() (DBGMCU->APB1LFZ1 \|= (DBGMCU_APB1LFZ1_DBG_TIM3))

#define	__HAL_DBGMCU_FREEZE_TIM4() (DBGMCU->APB1LFZ1 \|= (DBGMCU_APB1LFZ1_DBG_TIM4))

#define	__HAL_DBGMCU_FREEZE_TIM5() (DBGMCU->APB1LFZ1 \|= (DBGMCU_APB1LFZ1_DBG_TIM5))

#define	__HAL_DBGMCU_FREEZE_TIM6() (DBGMCU->APB1LFZ1 \|= (DBGMCU_APB1LFZ1_DBG_TIM6))

#define	__HAL_DBGMCU_FREEZE_TIM7() (DBGMCU->APB1LFZ1 \|= (DBGMCU_APB1LFZ1_DBG_TIM7))

#define	__HAL_DBGMCU_FREEZE_TIM12() (DBGMCU->APB1LFZ1 \|= (DBGMCU_APB1LFZ1_DBG_TIM12))

#define	__HAL_DBGMCU_FREEZE_TIM13() (DBGMCU->APB1LFZ1 \|= (DBGMCU_APB1LFZ1_DBG_TIM13))

#define	__HAL_DBGMCU_FREEZE_TIM14() (DBGMCU->APB1LFZ1 \|= (DBGMCU_APB1LFZ1_DBG_TIM14))

#define	__HAL_DBGMCU_FREEZE_LPTIM1() (DBGMCU->APB1LFZ1 \|= (DBGMCU_APB1LFZ1_DBG_LPTIM1))

#define	__HAL_DBGMCU_FREEZE_I2C1() (DBGMCU->APB1LFZ1 \|= (DBGMCU_APB1LFZ1_DBG_I2C1))

#define	__HAL_DBGMCU_FREEZE_I2C2() (DBGMCU->APB1LFZ1 \|= (DBGMCU_APB1LFZ1_DBG_I2C2))

#define	__HAL_DBGMCU_FREEZE_I2C3() (DBGMCU->APB1LFZ1 \|= (DBGMCU_APB1LFZ1_DBG_I2C3))

#define	__HAL_DBGMCU_FREEZE_TIM1() (DBGMCU->APB2FZ1 \|= (DBGMCU_APB2FZ1_DBG_TIM1))

#define	__HAL_DBGMCU_FREEZE_TIM8() (DBGMCU->APB2FZ1 \|= (DBGMCU_APB2FZ1_DBG_TIM8))

#define	__HAL_DBGMCU_FREEZE_TIM15() (DBGMCU->APB2FZ1 \|= (DBGMCU_APB2FZ1_DBG_TIM15))

#define	__HAL_DBGMCU_FREEZE_TIM16() (DBGMCU->APB2FZ1 \|= (DBGMCU_APB2FZ1_DBG_TIM16))

#define	__HAL_DBGMCU_FREEZE_TIM17() (DBGMCU->APB2FZ1 \|= (DBGMCU_APB2FZ1_DBG_TIM17))

#define	__HAL_DBGMCU_FREEZE_HRTIM() (DBGMCU->APB2FZ1 \|= (DBGMCU_APB2FZ1_DBG_HRTIM))

#define	__HAL_DBGMCU_FREEZE_I2C4() (DBGMCU->APB4FZ1 \|= (DBGMCU_APB4FZ1_DBG_I2C4))

#define	__HAL_DBGMCU_FREEZE_LPTIM2() (DBGMCU->APB4FZ1 \|= (DBGMCU_APB4FZ1_DBG_LPTIM2))

#define	__HAL_DBGMCU_FREEZE_LPTIM3() (DBGMCU->APB4FZ1 \|= (DBGMCU_APB4FZ1_DBG_LPTIM3))

#define	__HAL_DBGMCU_FREEZE_LPTIM4() (DBGMCU->APB4FZ1 \|= (DBGMCU_APB4FZ1_DBG_LPTIM4))

#define	__HAL_DBGMCU_FREEZE_LPTIM5() (DBGMCU->APB4FZ1 \|= (DBGMCU_APB4FZ1_DBG_LPTIM5))

#define	__HAL_DBGMCU_FREEZE_RTC() (DBGMCU->APB4FZ1 \|= (DBGMCU_APB4FZ1_DBG_RTC))

#define	__HAL_DBGMCU_FREEZE_IWDG1() (DBGMCU->APB4FZ1 \|= (DBGMCU_APB4FZ1_DBG_IWDG1))

#define	__HAL_DBGMCU_UnFreeze_WWDG1() (DBGMCU->APB3FZ1 &= ~ (DBGMCU_APB3FZ1_DBG_WWDG1))

#define	__HAL_DBGMCU_UnFreeze_TIM2() (DBGMCU->APB1LFZ1 &= ~ (DBGMCU_APB1LFZ1_DBG_TIM2))

#define	__HAL_DBGMCU_UnFreeze_TIM3() (DBGMCU->APB1LFZ1 &= ~ (DBGMCU_APB1LFZ1_DBG_TIM3))

#define	__HAL_DBGMCU_UnFreeze_TIM4() (DBGMCU->APB1LFZ1 &= ~ (DBGMCU_APB1LFZ1_DBG_TIM4))

#define	__HAL_DBGMCU_UnFreeze_TIM5() (DBGMCU->APB1LFZ1 &= ~ (DBGMCU_APB1LFZ1_DBG_TIM5))

#define	__HAL_DBGMCU_UnFreeze_TIM6() (DBGMCU->APB1LFZ1 &= ~ (DBGMCU_APB1LFZ1_DBG_TIM6))

#define	__HAL_DBGMCU_UnFreeze_TIM7() (DBGMCU->APB1LFZ1 &= ~ (DBGMCU_APB1LFZ1_DBG_TIM7))

#define	__HAL_DBGMCU_UnFreeze_TIM12() (DBGMCU->APB1LFZ1 &= ~ (DBGMCU_APB1LFZ1_DBG_TIM12))

#define	__HAL_DBGMCU_UnFreeze_TIM13() (DBGMCU->APB1LFZ1 &= ~ (DBGMCU_APB1LFZ1_DBG_TIM13))

#define	__HAL_DBGMCU_UnFreeze_TIM14() (DBGMCU->APB1LFZ1 &= ~ (DBGMCU_APB1LFZ1_DBG_TIM14))

#define	__HAL_DBGMCU_UnFreeze_LPTIM1() (DBGMCU->APB1LFZ1 &= ~ (DBGMCU_APB1LFZ1_DBG_LPTIM1))

#define	__HAL_DBGMCU_UnFreeze_I2C1() (DBGMCU->APB1LFZ1 &= ~ (DBGMCU_APB1LFZ1_DBG_I2C1))

#define	__HAL_DBGMCU_UnFreeze_I2C2() (DBGMCU->APB1LFZ1 &= ~ (DBGMCU_APB1LFZ1_DBG_I2C2))

#define	__HAL_DBGMCU_UnFreeze_I2C3() (DBGMCU->APB1LFZ1 &= ~ (DBGMCU_APB1LFZ1_DBG_I2C3))

#define	__HAL_DBGMCU_UnFreeze_TIM1() (DBGMCU->APB2FZ1 &= ~ (DBGMCU_APB2FZ1_DBG_TIM1))

#define	__HAL_DBGMCU_UnFreeze_TIM8() (DBGMCU->APB2FZ1 &= ~ (DBGMCU_APB2FZ1_DBG_TIM8))

#define	__HAL_DBGMCU_UnFreeze_TIM15() (DBGMCU->APB2FZ1 &= ~ (DBGMCU_APB2FZ1_DBG_TIM15))

#define	__HAL_DBGMCU_UnFreeze_TIM16() (DBGMCU->APB2FZ1 &= ~ (DBGMCU_APB2FZ1_DBG_TIM16))

#define	__HAL_DBGMCU_UnFreeze_TIM17() (DBGMCU->APB2FZ1 &= ~ (DBGMCU_APB2FZ1_DBG_TIM17))

#define	__HAL_DBGMCU_UnFreeze_HRTIM() (DBGMCU->APB2FZ1 &= ~ (DBGMCU_APB2FZ1_DBG_HRTIM))

#define	__HAL_DBGMCU_UnFreeze_I2C4() (DBGMCU->APB4FZ1 &= ~ (DBGMCU_APB4FZ1_DBG_I2C4))

#define	__HAL_DBGMCU_UnFreeze_LPTIM2() (DBGMCU->APB4FZ1 &= ~ (DBGMCU_APB4FZ1_DBG_LPTIM2))

#define	__HAL_DBGMCU_UnFreeze_LPTIM3() (DBGMCU->APB4FZ1 &= ~ (DBGMCU_APB4FZ1_DBG_LPTIM3))

#define	__HAL_DBGMCU_UnFreeze_LPTIM4() (DBGMCU->APB4FZ1 &= ~ (DBGMCU_APB4FZ1_DBG_LPTIM4))

#define	__HAL_DBGMCU_UnFreeze_LPTIM5() (DBGMCU->APB4FZ1 &= ~ (DBGMCU_APB4FZ1_DBG_LPTIM5))

#define	__HAL_DBGMCU_UnFreeze_RTC() (DBGMCU->APB4FZ1 &= ~ (DBGMCU_APB4FZ1_DBG_RTC))

#define	__HAL_DBGMCU_UnFreeze_IWDG1() (DBGMCU->APB4FZ1 &= ~ (DBGMCU_APB4FZ1_DBG_IWDG1))

#define	IS_TICKFREQ(FREQ)

Enumerations
enum	HAL_TickFreqTypeDef { HAL_TICK_FREQ_10HZ = 100U , HAL_TICK_FREQ_100HZ = 10U , HAL_TICK_FREQ_1KHZ = 1U , HAL_TICK_FREQ_DEFAULT = HAL_TICK_FREQ_1KHZ }

Functions
HAL_StatusTypeDef	HAL_Init (void)
	This function is used to initialize the HAL Library; it must be the first instruction to be executed in the main program (before to call any other HAL function), it performs the following: Configures the SysTick to generate an interrupt each 1 millisecond, which is clocked by the HSI (at this stage, the clock is not yet configured and thus the system is running from the internal HSI at 16 MHz). Set NVIC Group Priority to 4. Calls the HAL_MspInit() callback function defined in user file "stm32h7xx_hal_msp.c" to do the global low level hardware initialization.

HAL_StatusTypeDef	HAL_DeInit (void)
	This function de-Initializes common part of the HAL and stops the systick. This function is optional.

__weak void	HAL_MspInit (void)
	Initializes the MSP.

__weak void	HAL_MspDeInit (void)
	DeInitializes the MSP.

__weak HAL_StatusTypeDef	HAL_InitTick (uint32_t TickPriority)
	This function configures the source of the time base. The time source is configured to have 1ms time base with a dedicated Tick interrupt priority.

void	HAL_IncTick (void)
	This function is called to increment a global variable "uwTick" used as application time base.

void	HAL_Delay (uint32_t Delay)
	This function provides minimum delay (in milliseconds) based on variable incremented.

uint32_t	HAL_GetTick (void)
	Provides a tick value in millisecond.

uint32_t	HAL_GetTickPrio (void)
	This function returns a tick priority.

HAL_StatusTypeDef	HAL_SetTickFreq (HAL_TickFreqTypeDef Freq)
	Set new tick Freq.

HAL_TickFreqTypeDef	HAL_GetTickFreq (void)
	Return tick frequency.

void	HAL_SuspendTick (void)
	Suspend Tick increment.

void	HAL_ResumeTick (void)
	Resume Tick increment.

uint32_t	HAL_GetHalVersion (void)
	Returns the HAL revision.

uint32_t	HAL_GetREVID (void)
	Returns the device revision identifier.

uint32_t	HAL_GetDEVID (void)
	Returns the device identifier.

uint32_t	HAL_GetUIDw0 (void)
	Return the first word of the unique device identifier (UID based on 96 bits)

uint32_t	HAL_GetUIDw1 (void)
	Return the second word of the unique device identifier (UID based on 96 bits)

uint32_t	HAL_GetUIDw2 (void)
	Return the third word of the unique device identifier (UID based on 96 bits)

void	HAL_SYSCFG_AnalogSwitchConfig (uint32_t SYSCFG_AnalogSwitch, uint32_t SYSCFG_SwitchState)
	Analog Switch control for dual analog pads.

void	HAL_EnableCompensationCell (void)
	Enables the I/O Compensation Cell.

void	HAL_DisableCompensationCell (void)
	Power-down the I/O Compensation Cell.

void	HAL_SYSCFG_EnableIOSpeedOptimize (void)
	To Enable optimize the I/O speed when the product voltage is low.

void	HAL_SYSCFG_DisableIOSpeedOptimize (void)
	To Disable optimize the I/O speed when the product voltage is low.

void	HAL_SYSCFG_CompensationCodeSelect (uint32_t SYSCFG_CompCode)
	Code selection for the I/O Compensation cell.

void	HAL_SYSCFG_CompensationCodeConfig (uint32_t SYSCFG_PMOSCode, uint32_t SYSCFG_NMOSCode)
	Code selection for the I/O Compensation cell.

void	HAL_DBGMCU_EnableDBGSleepMode (void)
	Enable the Debug Module during Domain1/CDomain SLEEP mode.

void	HAL_DBGMCU_DisableDBGSleepMode (void)
	Disable the Debug Module during Domain1/CDomain SLEEP mode.

void	HAL_DBGMCU_EnableDBGStopMode (void)
	Enable the Debug Module during Domain1/CDomain STOP mode.

void	HAL_DBGMCU_DisableDBGStopMode (void)
	Disable the Debug Module during Domain1/CDomain STOP mode.

void	HAL_DBGMCU_EnableDBGStandbyMode (void)
	Enable the Debug Module during Domain1/CDomain STANDBY mode.

void	HAL_DBGMCU_DisableDBGStandbyMode (void)
	Disable the Debug Module during Domain1/CDomain STANDBY mode.

void	HAL_EXTI_EdgeConfig (uint32_t EXTI_Line, uint32_t EXTI_Edge)
	Configure the EXTI input event line edge.

void	HAL_EXTI_GenerateSWInterrupt (uint32_t EXTI_Line)
	Generates a Software interrupt on selected EXTI line.

void	HAL_EXTI_D1_ClearFlag (uint32_t EXTI_Line)
	Clears the EXTI's line pending flags for Domain D1.

void	HAL_EXTI_D1_EventInputConfig (uint32_t EXTI_Line, uint32_t EXTI_Mode, uint32_t EXTI_LineCmd)
	Configure the EXTI input event line for Domain D1.

void	HAL_EXTI_D3_EventInputConfig (uint32_t EXTI_Line, uint32_t EXTI_LineCmd, uint32_t EXTI_ClearSrc)
	Configure the EXTI input event line for Domain D3.

void	HAL_SetFMCMemorySwappingConfig (uint32_t BankMapConfig)
	Set the FMC Memory Mapping Swapping config.

uint32_t	HAL_GetFMCMemorySwappingConfig (void)
	Get FMC Bank mapping mode.

void	HAL_SYSCFG_VREFBUF_VoltageScalingConfig (uint32_t VoltageScaling)
	Configure the internal voltage reference buffer voltage scale.

void	HAL_SYSCFG_VREFBUF_HighImpedanceConfig (uint32_t Mode)
	Configure the internal voltage reference buffer high impedance mode.

void	HAL_SYSCFG_VREFBUF_TrimmingConfig (uint32_t TrimmingValue)
	Tune the Internal Voltage Reference buffer (VREFBUF).

HAL_StatusTypeDef	HAL_SYSCFG_EnableVREFBUF (void)
	Enable the Internal Voltage Reference buffer (VREFBUF).

void	HAL_SYSCFG_DisableVREFBUF (void)
	Disable the Internal Voltage Reference buffer (VREFBUF).

Variables
__IO uint32_t	uwTick

uint32_t	uwTickPrio

HAL_TickFreqTypeDef	uwTickFreq

Detailed Description

This file contains all the functions prototypes for the HAL module driver.

Author: MCD Application Team

Attention

This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.

Macros

Enumerations

Functions

Variables

Detailed Description